Information AboutPotentiometer |
| CATEGORIES ABOUT POTENTIOMETER | |
| measuring instruments | |
| resistive components | |
| transducers | |
| electrical components | |
|
A potentiometer is a variable resistor that can be used as a Voltage Divider . Originally a potentiometer was an instrument to measure the Potential (or voltage) in a circuit by tapping off a fraction of a known voltage from a resistive slide wire and comparing it with the unknown voltage by means of a Galvanometer . The present popular usage of the term potentiometer (or 'pot' for short) describes an electrical device which has a user-adjustable Resistance . Usually, this is a three-terminal resistor with a sliding contact in the center (the wiper). If all three terminals are used, it can act as a variable Voltage Divider . If only two terminals are used (one side and the wiper), it acts as a variable resistor. Its shortcoming is that of corrosion or wearing of the sliding contact, especially if it is kept in one position. POTENTIOMETER AS MEASURING INSTRUMENT The original potentiometer is a type of Bridge Circuit for measuring voltages by comparison between a small fraction of the voltage which could be precisely measured, then balancing the two circuits to get null current flow which could be precisely measured. The word itself derives from the phrase "voltage potential," and "potential" was used to refer to "strength." The original potentiometers are divided into four main classes: the constant resistance potentiometer, the constant current potentiometer, the microvolt potentiometer and the thermocouple potentiometer. Constant current potentiometer This is used for measuring voltages below 1.5 volts. In this circuit, the unknown voltage is connected across a section of resistance wire the ends of which are connected to a standard Electrochemical Cell that provides a constant Current through the wire, The unknown emf, in series with a galvanometer, is then connected across a variable-length section of the resistance wire using a sliding contact(s). The sliding contact is moved until no current flows into or out of the standard cell, as indicated by a Galvanometer in series with the unknown emf. The voltage across the selected section of wire is then equal to the unknown voltage. All that remains is to calculate the unknown voltage from the current and the fraction of the length of the resistance wire that was connected to the unknown emf. The galvanometer does not need to be calibrated, as its only function is to read zero. When the galvanometer reads zero, no current is drawn from the unknown electromotive force and so the reading is independent of the source's internal resistance. Constant resistance potentiometer The constant resistance potentiometer is a variation of the basic idea in which a variable current is fed through a fixed resistor. These are used primarily for measurements in the millivolt and microvolt range. Microvolt potentiometer This is a form of the constant resistance potentiometer described above but designed to minimize the effects of contact resistance and thermal emf. This equipment is satisfactorily used down to readings of 10 nV or so. Thermocouple potentiometer Another development of the standard types was the 'thermocouple potentiometer' especially modified for performing temperature measurements with thermocouples. {Link without Title} POTENTIOMETER AS ELECTRONIC COMPONENT In modern usage, a potentiometer is a Potential Divider , a three terminal Resistor where the position of the sliding connection is user adjustable via a knob or slider. Potentiometers are sometimes provided with one or more switches mounted on the same shaft. For instance, when attached to a volume control, the knob can also function as an on/off switch at the lowest volume. Ordinary potentiometers are rarely used to control anything of significant power (even lighting) directly due to resistive losses, but they are frequently used to adjust the level of analog signals (e.g. Volume controls on Audio Equipment ) and as control inputs for electronic circuits (e.g. a typical domestic light dimmer uses a potentiometer to set the point in the cycle at which the Triac turns on). Potentiometers used to control high power are normally called Rheostats . Types of potentiometers Low-power types A potentiometer is constructed using a flat Graphite annulus (ring) as the resistive element, with a sliding contact (wiper) sliding around this annulus. The wiper is connected to an axle and, via another rotating contact, is brought out as the third terminal. On panel pots, the wiper is usually the centre terminal. For single turn pots, this wiper typically travels just under one revolution around the contact. 'Multiturn' potentiometers also exist, where the resistor element may be Helical and the wiper may move 10, 20, or more complete revolutions. In addition to graphite, other materials may be used for the resistive element. These may be resistance wire or Carbon particles in plastic or a ceramic/metal mixture called Cermet . One popular form of rotary potentiometer is called a ''string pot''. It is a multi-turn potentiometer with an attached reel of wire turning against a spring. It's very convenient for measuring movement and therefore acts as a position transducer. In a linear slider pot, a sliding control is provided instead of a dial control. The word ''linear'' also describes the geometry of the resistive element which is a rectangular strip, (not an Annulus as in a rotary potentiometer). Because of their construction, this type of pot has a greater potential for getting contaminated. Potentiometers can be obtained with either Linear or Logarithm ic laws (or " Taper s"). potentiometers, or "trimpots", intended for infrequent adjustment.]] = Linear potentiometers A ''linear pot'' has a resistive element of constant cross-section, resulting in a device where the resistance between the contact (wiper) and one end terminal is Proportional to the distance between them. ''Linear'' describes the electrical 'law' of the device, not the geometry of the resistive element. = Logarithmic potentiometers A ''log pot'' has a resistive element that either 'tapers' in from one end to the other, or is made from a material whose resistivity varies from one end to the other. This results in a device where output voltage is a logarithmic (or inverse logarithmic depending on type) function of the mechanical angle of the pot. Most (cheaper) "log" pots are actually not logarithmic, but use two regions of different, but constant, resistivity to approximate a logarithmic law. A log pot can also be simulated with a linear pot and an external resistor. True log pots are significantly more expensive. High-power types A rheostat is essentially a potentiometer, but is usually much larger, designed to handle much higher voltage and current. Typically these are constructed as a resistive wire wrapped to form a Toroid coil (or most of one) with the wiper moving over the upper surface of the toroid, sliding from one turn of the wire to the next. Sometimes a rheostat is made from resistance wire wound on a heat resisting cylinder with the slider made from a number of metal fingers that grip lightly onto a small portion of the turns of resistance wire. The 'fingers' can be moved along the coil of resistance wire by a sliding knob thus changing the 'tapping' point. They are usually used as variable resistors rather than variable potential dividers. Digital control Digitally Controlled Potentiometers (DCPs) or Digipot s can be used in analogue Signal Processing circuits to replace potentiometers. They allow small adjustments to be made to the circuit by software, instead of a mechanical adjustment. Because this type of control is updated only infrequently, it often has a slow Serial interface, like I&2C . Some types have non-volatile memory to enable them to remember their last settings when the power is switched off. The same idea can be used to create Digital Volume Controls, Attenuator s, or other controls under digital control. Usually such devices feature quite a high degree of accuracy, and find applications in instrumention, Mixing Desk s and other precision systems. The DCP should not be confused with the Digital To Analogue Converter (DAC) which actually creates an analogue signal from a digital one. A DCP only controls an existing analogue signal digitally. However, some DACs using resistive R-2R architecture have been functionally used as DCPs where the (varying) analogue signal is input to the reference voltage pin of the DAC and the digitally-controlled attenuated output is taken from the output of the DAC. Applications of potentiometers Transducers Potentiometers are also very widely used as a part of Displacement Transducer s because of the simplicity of construction and because they can give a large output signal. Audio control One of the most common uses for modern low-power potentiometers is as audio control devices. Both sliding pots (also known as faders) and rotary potentiometers (commonly called knobs) are regularly used to adjust loudness, frequency attenuation and other characteristics of audio signals. The 'log pot' is used as the volume control in Audio Amplifier s, where it is also called an "audio taper pot", because the Amplitude response of the human Ear is also logarithmic. It ensures that, on a volume control marked 0 to 10, for example, a setting of 5 sounds half as loud as a setting of 10. There is also an ''anti-log pot'' or ''reverse audio taper'' which is simply the reverse of a log pot. It is almost always used in a ganged configuration with a log pot, for instance, in an audio balance control. A potentiometer used in combination with an inductor or capacitor acts as a "tone" Control . THEORY OF OPERATION The 'modern' potentiometer can be used as a ''potential divider'' (or '' Voltage Divider '') to obtain a manually adjustable output voltage at the slider (wiper) from a fixed input voltage applied across the two ends of the pot. This is the most common use of pots. The voltage across is determined by the formula: : |
|
|