Information AboutChisel |
| CATEGORIES ABOUT CHISEL | |
| mechanical hand tools | |
| woodworking hand tools | |
| metalworking | |
| stonemasonary tools | |
|
A chisel is a Tool with a characteristically shaped Cutting Edge (such that wood chisels have lent part of their name to a particular Grind ) of blade on its end, for carving and/or cutting a hard material such as Wood , Stone , or Metal . The handle and blade of some types of chisel are made of metal or wood with a sharp edge in it. In use, the chisel is forced into the material to cut the material. The driving force may be manually applied or applied using a Mallet or Hammer . In industrial use, a Hydraulic Ram or falling weight (' Trip Hammer ') drives the chisel into the material to be cut. A '' Gouge '', one type of chisel, is used, particularly in Woodworking , Woodturning and Sculpture , to carve small pieces from the material. Gouges are most often used in creating concave surfaces. A gouge typically has a 'U'-shaped cross-section. TYPES Chisels have a wide variety of uses. Many types of chisels have been devised, each specially suited to its intended use. Different types of chisels may be constructed quite differently, in terms of blade width or length, as well as shape and hardness of blade. They may have wooden handles attached or may be made entirely of one piece of metal. Woodworking chisels Woodworking chisels range from quite small hand tools for tiny details, to large chisels used remove big sections of wood, in 'roughing out' the shape of a pattern or design. Typically, in woodcarving, one starts with a larger tool, and gradually progresses to smaller tools to finish the detail. One of the largest types of chisel is the Slick , used in Timber Frame Construction and wooden shipbuilding. According to their function there are many names given to woodworking chisels, such as:
Lathe tools A Lathe tool can be a woodworking chisel designed to cut wood as it is spun on a lathe. These tools have longer handles for more leverage, needed to counteract the tendency of the tool to react to the downward force of the spinning wood being cut or carved. In addition, the angle and method of sharpening is different, a secondary bevel would not be ground on the tool. Metalworking chisels Chisels used in metal work can be divided into two main categories, ''hot'' chisels, and ''cold'' chisels. A hot chisel is used to cut metal that has been heated in a Forge to soften the metal. Cold chisel A cold chisel is a tool made of Tempered Steel used for cutting 'cold' metals, meaning that they are not used in conjunction with heating torches, forges, etc. This tool is also commonly referred to by the Misnomer 'coal chisel'. Because cold chisels are used to form metal, they have a less-acute angle to the sharp portion of the blade than a woodworking chisel. This gives the cutting edge greater strength at the expense of sharpness. Cold chisels come in a variety of sizes, from fine engraving tools that are tapped with very light hammers, to massive tools that are driven with Sledgehammer s. Hardy chisel A hardy chisel is a type of hot chisel with a square Shank , which is held in place with the cutting edge facing upwards by placing it in an Anvil 's Hardy Hole . The hot workpiece cut is then placed over the hardy, and struck with a hammer. The hammer drives the chisel into the hot metal, allowing it to be snapped off with a pair of Tongs . Stone chisels Stone chisels are used to carve or cut stone, bricks or concrete slabs. To cut, as opposed to carve, a brick bolster is used; this has a wide, flat blade that is tapped along the cut line to produce a groove, then hit hard in the centre to crack the stone. To increase the force, stone chisels are often hit with Club Hammer s, a heavier type of hammer. Masonry chisels Masonry chisels are typically heavy, with a relatively dull head that wedges and breaks, rather than cuts. Normally used as a demolition tool, they may be mounted on a Hammer-drill , Jack Hammer , or hammered manually, usually with a heavy Hammer of three pounds or more. Plugging chisel A Plugging chisel has a tapered edge for cleaning out hardened Mortar . The chisel is held with one hand and struck with a hammer. The direction of the taper in the blade determines if the chisel cuts deep or runs shallow along the joint. SEE ALSO EXTERNAL LINKS
|
|
|