| Square Rigged |
Article Index for Square |
Website Links For Square |
Information AboutSquare Rigged |
| CATEGORIES ABOUT SQUARE RIG | |
| sailing vessels and rigging | |
|
Square rig is a generic type of sail and rigging arrangement in which the primary driving sails are carried on horizontal Spar s which are perpendicular to the Keel of the vessel and to the masts. These spars are called '' Yards '', the tips of which, beyond the last stay, are called the ''yardarms''. A ship at least partially so rigged is called a square rigger. It can also describe individual, four-cornered Sail s suspended from the horizontal yards, and carried on either a square rigged or a mainly Fore-and-aft Rig ged vessel, such as one with either a Bermuda Rig ged or Gaff Rig ged Mainsail . The term is also used for the uniform of a rating in the Royal Navy from 1857 onwards. It is slang and refers to anyone wearing the non-peaked cap worn by Petty Officer s and Officers this 'rig' includes the famous blue collar on the shoulders and bell-bottomed trousers. This name perhaps reflects the fact that it was these men who managed the square rigged sails. A Mast is considered square rigged if its lowest sail or Course is square rigged, but normally if this is the case it will have a complete set of square rigged sails. If the course is fore-and-aft, square topsails can still be carried in front of the mast. .]] Square-rigged masts may also have staysails that are deployed fore-and-aft between masts. CHARACTERISTICS OF SQUARE RIG In their heyday, square-rigged vessels ranged in size from small boats to Full Rigged Ship s, however, today this rig has fallen from favour and the rig in common use today is one form or another of fore-and-aft Gaff Rig s and Bermuda Rig s. The reason for this change are the development of steam power and new materials. For larger ships, it was only possible to drive large tonnages using multiple sails until steam arrived and made sails unnecessary, although hybrids existed for a while. The strains imposed on cordage and sails in the Age of Sail meant that a large number of sails were necessary to get the surface area necessary to drive larger ships. Fewer larger sails would not have survived the rigours of the larger commercial and military ships and required more men to manage. Therefore, in order to get the large number of sails to effectively collect wind and provide motive power they had to be square to the hull. There were no examples of the more efficient fore-and-aft rigs on larger vessels for this reason. Despite the large overall sail areas, and even when sailing on their best points of sail, it was sometimes the case that large warships could only make 6-8 knots, while some of the faster clippers for whom speed was critical could make much faster speeds, e.g. Cutty Sark which could make 17 knots. The square rig breaks up the sail area into many smaller sails, each of which can be individually handled by a relatively small team hauling on their controlling lines. Having many smaller sails also allowed warships to manage the impact of weapons upon them. Instead of losing one very large sail to a hole from a cannonball, which would then tear, the damage was constrained to a much smaller sail area and, therefore, had less impact on the motive power of the vessel. With the development of more advanced fittings, equipment and cordage, particularly geared winches, high loads on an individual line (or rope) became less of an issue, and the focus moved to minimising the number of lines and hence the size of the crew needed to handle them. It is particularly in the area of hybrid vessels carrying some square-rigged sails that changes due to materials are noticeable. The low Aspect Ratio of square rigged sails (usually 1/2 to 1/3) produce large amounts of drag for the lift (motive power) that they produce, and thus give very poor performance to Windward . This means that they cannot sail as close to the wind. The Bermuda rig is the (nearly) undisputed champion of windward performance in soft sails, due to its very low drag and high lift to drag ratio. Square rigs do have their advantages, however; they are more efficient when Running , where the high lift to drag is irrelevant and the total drag is the most important issue. Square rigged sails are less prone to Broaching when running than Bermuda rigs. On a square rigged mast the sails had names which indicated their position on the mast. The lowest square sail was the course, the next sail up the mast was called the topsail, the next the topgallant sail. Some vessels shipped a fourth, sail called the royal, above the other three. Sometimes a vessel might put out Studding Sails which would be fixed outboard of the sail on both sides of it. Beginning in the mid-nineteenth century, the topsails and topgallants were each split into upper and lower sails; this allowed smaller crews to tend the sails and provided captains with a greater set of options in choosing which sails to set. Sails are referred to by their mast and then name, ''e.g.'', "the fore topgallant sail", often shortened to fore t'gallant. SAIL CHARACTERISTICS A square rigged sail is not in fact square, but more nearly Trapezoid al, being symmetrical but longer in the Foot than the Head . Like all sails it is three-dimensional, and its curve or belly means that its foot (lower edge) is not a straight line at all. It is fixed to a spar (the yard) along its head, and its Clew s (bottom corners) are controlled by Sheet s, often run to Blocks on the spar immediately below the sail. Modern square-rigged ships are still used for Training , tourism and ceremonial purposes. TYPES OF SQUARE RIG Principally square rigged types
All the above rigs normally carry a number of Jib s and at least one Spanker , and generally carry fore-and-aft Staysail s between the masts. Fore-and-aft rigs with some square rigged sails
EXTERNAL LINKS
|
|
|