Information AboutSkateboard |
| CATEGORIES ABOUT SKATEBOARD | |
| skateboarding | |
|
A skateboard is a four wheeled platform used for the activity of Skateboarding . It is propelled by pushing with one foot while the other remains on the board, or by pumping in structures such as a half-pipe or bowl. Or a skateboard can simply be stood on while on an incline and allowing gravity to propel the board and rider. That being said, the skateboard is not easily defined. Unlike most other sports, there is no governing body which declares any regulations on what constitutes a skateboard or the parts that it is assembled from. Thus, a skateboard can vary wildly in both appearance and performance. There is no definitive origin or inventor of the skateboard. One proposed origin is that skateboards arose in the 1940s and 1950s, when children would participate in Soapbox (car) races, using soap-boxes attached to wooden planks on Rollerskate wheels. When the soap-box became detached from the plank, children would ride these primitive "skateboards". Another suggests that the skateboard was created directly from the adaptation of a single rollerskate taken apart and nailed to a 2x4, without the soapbox at all. The skateboard has evolved since the first mass produced models in the 1960s. Boards in the past were often made in the shape of a surfboard, with no concavity and constructed of solid wood or plastic. The wheels were usually made of a clay composite, or steel and the trucks (axles) were less sturdy and initially of a 'single-action' design compared to today's 'double-action'. A Longboard is a skateboard with a longer wheelbase, and typically larger and softer wheels. Longboard trucks are taller with longer axles for stability; and are often ridden looser, allowing for easier turning. This may explain why longboards are given the nickname "sidewalk surfer". There are many numbers of specific disciplines within the longboard community, including: slalom, free-ride, rhythmic/ dance, and slopestyle. PARTS Descriptions of the following skateboard parts are the ones most prevalent in popular, modern forms of skateboarding. Many niche disciplines exist with exotic or alternative constructions and designs that fall outside of much of the descriptions listed. Skateboards are composed of the following parts. Deck Most decks are constructed with a seven . Sometimes other, more exotic materials, such as fiberglass, bamboo, Kevlar, carbon fiber, and plastic are incorporated into deck construction, usually to lighten the board or increase its strength or rigidity. Modern decks are 7 to 8½ inches wide. The width of a deck depends on the personal preference of the person who uses it. Most people use 7.5-8 inch wide decks for street skating. Generally, riders use a wider deck for vert, to provide more stability. Skateboard decks are usually between 28 and 33 inches long. The Longboard , a common variant of the skateboard, has a longer deck. "Old school" boards (those made in the 1970s-80s or modern boards that mimic their shape) are generally wider and often have only one kicktail. 1970s variants often have little or no concave, whereas 1980s models have deeper concaves and steeper kicktails. The double-kicktail skateboard was not introduced until the 1980s. By adding an extra "tail" to the front of the deck, possibilities were multiplied drastically. This also led to nollie, fakie, and switch stances. Most decks are pressed with concave in the body, i.e. the area of the board between the nose and the tail kicks. Concave means the deck dips inward on the top side (where the skater stands), to cup the foot for more control, and to add strength by stiffening the flex. Trucks Attached to the deck are two metal (usually aluminum alloy) trucks, which connect to the wheels and deck. The trucks are further composed of two parts. The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are '' Bushing s'', also ''rubbers'' or '' Grommet s'', that provide the cushion mechanism for turning the skateboard. The '' Bushing s'' cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. A bolt called a '' Kingpin '' holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted for steering. Wheels
Bearings Each skateboard wheel is mounted on its axle via two Ball Bearing s. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8mm, an outer diameter of 22mm, and a width of 7mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC Scale . It is a common misconception that higher numbers are better for skateboarding, but the ABEC rating only measures tolerances which do not necessarily apply to skateboards. The ABEC rating does not determine how fast or how durable a bearing used for skateboarding will be. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. {Link without Title} {Link without Title} {Link without Title} Hardware Mounting hardware is a set of eight 10-32 bolts, usually a flat head, and matching self-lock nylock nuts. They are used to attach the trucks to the board. OPTIONAL COMPONENTS Rails Narrow strips of plastic that are fastened under the deck lengthwise along the edges. Used for additional grip for grabs, and to enhance sliding while protecting the deck's graphics at the same time. Not to be confused with the obstacle also known as a rail which tricks are performed on. Lappers A lapper is a plastic cover that is fastened to the rear truck and serves to protect the kingpin when grinding. It also prevents hang-ups by providing a smoother transition for the truck when it hits an obstacle. Nose guard A plastic bumper used to protect the tip of a skateboard. Tail guard A tail guard is a plastic skid plate used to prevent wearing of the tail, and is used as a means to stop the board. Risers Riser or riser pads are made of plastic and go between the truck and the board to provide additional clearance for the wheels to prevent wheel-bite (when the truck turns to a degree where the wheel will contact with the deck and stop spinning). They usually range in height from ⅛″ to ½″. Shock pads are a variation of risers that are usually made of rubber or neoprene. They absorb impact and reduce vibration, which in turn helps prevent hardware from loosening and they can also prevent pressure cracks from forming. REFERENCES SEE ALSO |
|
|