| Heat Pipe |
Article Index for Heat |
Website Links For Heat |
Information AboutHeat Pipe |
| CATEGORIES ABOUT HEAT PIPE | |
| hvac | |
| computer hardware cooling | |
| heat conduction | |
|
A heat pipe is a heat transfer mechanism that can transport large quantities of heat with a very small difference in Temperature between the hot and cold interfaces. CONSTRUCTION A typical heat pipe consists of sealed hollow tube made of a thermoconductive metal such as Copper or Aluminium . The pipe contains a relatively small quantity of a "working fluid" or Coolant (such as Water , Ethanol or Mercury ) with the remainder of the pipe being filled with vapour phase of the working fluid, all other gases being excluded. Internally, in order to overcome gravitational forces (or because of their absence in the case of space applications) most heat pipes contain a wick structure. This typically consists of metal powder Sintered onto the inside walls of the tube, but may in principle be any material capable of soaking up the coolant. Heat pipes contain no moving parts and typically require no maintenance, though non-condensing gases that diffuse through the walls of the pipe may eventaully reduce the effectiveness, particularly when the vapour pressure of the working fluid is low. The choice of materials and coolant depends on the temperature conditions in which the heat pipe must operate, with coolants ranging from liquid Helium for extremely low temperature applications to Mercury for high temperature conditions. The advantage of heat pipes is their great efficiency in transferring heat. They are actually more "conductive" than a copper bar of equivalent cross-section. MECHANISM Heat pipes employ Evaporative Cooling to transfer thermal energy from one point to another by the Evaporation and Condensation of a working fluid or coolant. Heat pipes rely on a temperature difference between the ends of the pipe, and cannot lower temperatures at either end beyond the ambient temperature (hence they tend to equalise the temperature within the pipe). When one end of the heat pipe is heated the working fluid inside the pipe at that end evaporates and increases the vapour pressure inside the cavity of the heat pipe. The Latent Heat of evaporation absorbed by the vaporisation of the working fluid reduces the temperature at the hot end of the pipe. The vapour pressure over the hot liquid working fluid at the hot end of the pipe is higher than the equilbrium vapour pressure over condensing working fluid at the cooler end of the pipe, and this pressure difference drives a rapid mass transfer to the condensing end where the excess vapour releases its latent heat, warming the cool end of the pipe. Non-condensing gases in the vapour impede the gas flow, and reduce the effectiveness of the heat pipe, particularly at low temperatures, where vapour presures are low. The condensed working fluid then flows back to the hot end of the pipe, either by force of gravity in the case of vertically oriented heat pipes, or through Capillary Action in the case of heat pipes containing wicks, or heat pipes that are orientated horizontally relative to gravity. In summary inside a heat pipe "hot" vapor flows in one direction, condenses to the liquid phase which flows back in the other direction to evaporate again and close the cycle. ORIGINS While the general principle of heat pipes using gravity dates back to the steam age, the benefits of employing capillary action were first noted by George Grover at Los Alamos National Laboratory in 1963 and subsequently published in the Journal Of Applied Physics in 1964. Grover noted in his notebook: (from )
APPLICATIONS Grover and his colleagues were working on cooling systems for Nuclear Power Cells for Space Craft , where extreme thermal conditions are found. Heat pipes have since been used extensively in space craft as a means for managing internal temperature conditions. Heat pipes are extensively used in many modern computer systems, where increased power requirements and subsequent increases in heat emission have resulted greater demands on cooling systems. Heat pipes are typically used to move heat away from components such as CPU s and GPU s to heat sinks where thermal energy may be dissipated into the environment. LIMITATIONS Heat pipes must be tuned to particular cooling conditions. The choice of pipe material, size and coolant all have an effect on the optimal temperatures in which heat pipes work. When heated above a certain temperature, all of the working fluid in the heat pipe will vaporize and the condensation process will cease to occur; in such conditions, the heat pipe becomes completely ineffective. REFERENCES | ||
| Author | Grover, GM, T P Cotter, and G F Erickson |
|
| Year | 1964 |
|
| Title | Structures of Very High Thermal Conductance |
|
| Journal | Journal of Applied Physics |
|
| Volume | 35 |
|
| Issue | 6 |
|
| Pages | 1990-1991 |
|
|