| Descriptive Geometry |
Article Index for Descriptive |
Shopping Descriptive |
Website Links For Geometry |
Information AboutDescriptive Geometry |
| CATEGORIES ABOUT DESCRIPTIVE GEOMETRY | |
| descriptive geometrydescriptive geometry | |
| technical drawing | |
|
Using Monge's protocols allows an imaginary object to be drawn so that it may be 3-D modeled. That is, all geometric aspects of the imaginary object are accounted for in true size/to-scale and shape, and then imaged as seen from any direction of space; all on a two-dimensional drawing surface. Descriptive geometry uses the image-creating technique of imaginary, parallel projectors emanating from an imaginary object and intersecting an imaginary plane of projection at right angles. The cumulative points of intersections create the desired image. See Orthographic Projection , Multiviews Without Rotation . PROTOCOLS
Aside from the Orthographic, six standard principal views (Front; Right Side; Left Side; Top; Bottom; Rear), descriptive geometry strives to yield three basic solution views: the true length of a line (i.e., full size, not foreshortened), the point view (end view) of a line, and the true shape of a plane (i.e., full size to scale, or not foreshortened). These often serve to determine the direction of projection for the subsequent view. By the 90° circuitous stepping process, projecting in any direction from the point view of a line yields its true length view; projecting in a direction parallel to a true length line view yields its point view, projecting the point view of any line on a plane yields the plane's edge view; projecting in a direction perpendicular to the edge view of a plane will yield the true shape (to scale) view. These various views may be called upon to help solve engineering problems posed by solid-geometry principles. HEURISTICS There is heuristic value to studying descriptive geometry. It promotes visualization and spatial analytical abilities. It promotes intuitive ability to recognize the direction of viewing for best presenting a geometric problem for solution. Representative examples: The direction to best view:
A standard for presenting computer-modeling views analogous to orthographic, sequential projections has not yet been adopted. One candidate for such is presented in the illustrations below. The images in the illustrations were created using three-dimensional, engineering computer graphics. Three-dimensional, computer modeling produces virtual space "behind the tube", as it were, and may produce any view of a model from any direction within this virtual space. It does so without the need for adjacent orthographic views and therefore renders the circuitous, stepping protocol of Descriptive Geometry as obsolete. GENERAL SOLUTIONS General solutions are a class of solutions within descriptive geometry that contain all possible solutions to a problem. The general solution is represented by a single, three-dimensional object, usually a cone, the directions of the elements of which are the desired direction of viewing (projection) for any of an infinite number of solution views. For example: To find the general solution such that two, unequal length, skew lines in general positions (say, rockets in flight?) appear:
In the examples, the general solution for each desired characteristic solution is a cone, each element of which produces one of an infinite number of solution views. When two or more characteristics of, say those listed above, are desired (and for which a solution exists) projecting in the direction of either of the two elements of intersections (one element, if cones are tangent) between the two cones produces the desired solution view. If the cones do not intersect a solution does not exist. The examples below are annotated to show the descriptive geometric principles used in the solutions. TL = True-Length; EV = Edge View. Figs. 1-3, below, demonstrate (1) Descriptive geometry, general solutions and (2) simultaneously, a potential standard for presenting such solutions in orthographic, multiview, layout formats. The potential standard employs two, adjacent, standard, orthographic views (here, Front and Top) with a standard "folding line" between. As there is no subsequent need to 'circuitously step' 90° around the object, in standard, two-step sequences in order to arrive at a solution view (it is possible to go directly to the solution view), this shorter protocol is accounted for in the layout. Where the one step protocol replaces the two-step protocol, "double folding" lines are used. In other words, when one crosses the double lines he is not making a circuitous,90° turn but a non-orthodirectional turn directly to the solution view. As most engineering computer graphics packages automatically generates the six principal views of the glass box model, as well as an isometric view, these views are sometimes added out of heuristic curiosity. ''Figure 1: Descriptive geometry - skew lines appearing perpendicular'' ''Figure 2: Descriptive geometry - skew lines appear equal length'' ''Figure 3: Descriptive geometry - skew lines appear in specified length ratio'' SEE ALSO
|
|
|