| En 13402 |
Article Index for En |
Information AboutEn 13402 |
| CATEGORIES ABOUT EN 13402 | |
| sizes in clothing | |
| en standards | |
| metrication | |
| fashion design | |
|
There are three approaches for size-labeling of clothes:
Traditionally, clothes have been labeled using many different ad-hoc size systems. This approach has led to a number of problems:
Therefore, the European standards body CEN started in 1996 the process of designing a new modern system of labeling clothes sizes, resulting in the standard EN 13402 "Size designation of clothes". It is based on
The EN 13402 standard consists of four parts: EN 13402-1: TERMS, DEFINITIONS AND BODY MEASUREMENT PROCEDURE The first part of the standard defines the list of body dimensions to be used for designating clothes sizes, together with an anatomical explanation and measurement guidelines: ; head girth : maximum Horizontal Girth of the Head measured above the Ear s ; neck girth : girth of the neck measured with the Tape Measure passed 2 cm below the Adam's Apple and at the level of the 7th Cervical Vertebra ; chest girth : maximum horizontal girth measured during normal breathing with the subject standing erect and the tape-measure passed over the Shoulder Blade s (scapulae), under the Armpits (axillae), and across the Chest ; bust girth : maximum horizontal girth measured during normal breathing with the subject standing erect and the tape-measure passed horizontally, under the armpits (axillae), and across the Bust prominence (preferably measured with moderate tension over a Brassiere that shall not deform the Breast in an unnatural way and shall not displace its volume) ; underbust girth : horizontal girth of the body measured just below the Breast s ; waist girth : girth of the natural Waist line between the top of the Hip Bone s (iliac crests) and the lower Rib s, measured with the subject breathing normally and standing erect with the Abdomen relaxed ; hip girth : horizontal girth measured round the Buttocks at the level of maximum circumference ; height : vertical distance between the crown of the head and the soles of the feet, measured with the subject standing erect without shoes and with the feet together (for infants not yet able to stand upright: length of the body measured in a straight line from the crown of the head to the soles of the feet) ; inside leg length : distance between the Crotch and the soles of the feet, measured in a straight vertical line with the subject erect, feet slightly apart, and the weight of the body equally distributed on both legs ; arm length : distance, measured using the tape-measure, from the armscye/shoulder line intersection ( Acromion ), over the elbow, to the far end of the prominent wrist bone ( Ulna ), with the subject's right fist clenched and placed on the hip, and with the arm bent at 90° ; hand girth : maximum girth measured over the knuckles ( Metacarpal s) of the open right hand, fingers together and thumb excluded ; foot length: horizontal distance between perpendiculars in contact with the end of the most prominent toe and the most prominent part of the heel, measured with the subject standing barefoot and the weight of the body equally distributed on both feet ; body mass : measured with a suitable balance in kilograms These dimensions are meant to be measured preferably without or as few as possible clothes. All body dimensions are measured in centimeters, except for the body mass. The standard also defines a pictogram that can be used in language-neutral labels to indicate one or several of the above body dimensions. EN 13402-2: PRIMARY AND SECONDARY DIMENSIONS The second part of the standard defines for each type of garment one "primary dimension". This is the body measure according to which the product must be labelled. For some types of garment, a single measure may not be sufficient to select the right product. In these cases, one or two "secondary dimensions" can be added to the label. The following table shows the primary and secondary dimensions listed in the standard. Secondary dimensions are shown in parenthesis. EN 13402-3: MEASUREMENTS AND INTERVALS The third part of the standard defines Preferred Number s of primary and secondary body dimensions. The product should not be labeled with the average body dimension for which the garment was designed (i.e., not "height: 176"). Instead, the label should show the range of body dimensions from half the step size below to half the step size above the design size (e.g., "height: 172-180"). For heights, for example, the standard recommends generally to use the following design dimensions, with a step size of 8 cm: For trousers, the recommended step size for height is 4 cm: The standard defines similar tables for other dimensions and garments, only some of which are shown here. Men The standard sizes and ranges for chest and waist girth are: The above table is for ''drop'' = −12 cm, where : ''drop'' = ''waist girth'' − ''chest girth''. Example: While manufacturers will typically design clothes for ''chest girth'' = 100 cm such that it fits ''waist girth'' = 88 cm, they may also want to combine that ''chest girth'' with neighboring ''waist girth'' step sizes 84 cm or 92 cm, to cover these drop types (−16 cm and −8 cm) as well. The standard also suggests that neck girth can be associated with chest girth according to this table: The standard further suggests that arm length can be associated with height according to this table: Women Dress sizes The standard sizes and ranges for bust, waist and hip girth are: Bra sizes The standard sizes for brassiere are: The secondary dimension ''cup size'' can be expressed in terms of the difference : ''cup size'' = ''bust girth'' − ''underbust girth'' and can be labeled compactly using a letter code appended to the ''underbust girth'': Example: Bra size 70B is suitable for women with ''underbust girth'' 68-72 cm and ''bust girth'' 84-86 cm. Letter codes For clothes where a larger step size is sufficient, the standard also defines a letter code. This code represents the bust girth for women and the chest girth for men. The standard does not define such a code for children. Each range combines two adjacent size steps. The ranges could be extended below XXS or above 3XL if necessary, for example: EN 13402-4: CODING SYSTEM The fourth part of the standard is still under review and is expected to be published in early 2006. It describes a compact coding system for clothes sizes. It is mostly intended for industry to use in databases and as a part of stock-keeping identifiers and catalogue ordering numbers. Writing out all the centimetre figures of all the primary and secondary measures from EN 13402-2 can in some cases require up to 12 digits. The full list of centimeter figures on the pictogram contains a lot of redundancy and the same information can be squeezed into fewer digits with lookup tables. EN 13402-4 defines several such tables. They list all in-use combinations of EN 13402-3 measures and assign a short 2- or 3-digit code to each. RELATED LINKS EXTERNAL LINKS
|
|
|